You turn the key and the car won't start? Before you call a tow truck: most of the time it's a simple fault you can find yourself in a few minutes. This guide explains, with a 3D model, how the starting, charging and ignition systems work, and 4 simple cases that tell you where the fault is.
Video: Car Won't Start? Find the Fault Step by Step – Battery, Starter, Ignition or Fuel (3D Animation), 5:19 min, by Auto Oprema. The video has English and Serbian audio (choose the audio track in the ⚙ settings) and subtitles.
The video is published on 20 November 2026. Until then the player shows that it is not yet available; the guide below is already complete.
Quick answer: what happens when you turn the key?
- Nothing happens, lights dim: battery, terminals or the cable to the starter.
- Starter whirs, engine doesn't turn: solenoid, drive pinion or flywheel ring gear. One click with a good battery: solenoid, starter or its supply.
- Engine cranks but won't start: ignition (glow plugs, spark plugs, coils) or a sensor – a rev counter that stays at zero points to the crankshaft sensor.
- Ignition is fine: check the fuel supply – pump, fuse, relay, filter.
The starting system
The starting system has five main parts: the battery, the ignition switch, the starter relay, the starter motor and the flywheel. When you turn the key to START, current flows from the battery through the relay to the starter. Its solenoid pushes the small pinion into the flywheel ring gear, and the electric motor turns the engine. When the engine runs, the current is cut and a spring pulls the pinion back.
Never turn the key to START while the engine is running – the pinion tries to engage a spinning flywheel, the gears grind and the teeth on both the pinion and the ring gear get damaged.
The charging system
Until the engine starts, the battery powers everything. Then the alternator, driven by the crankshaft through a belt, takes over. The spinning rotor creates a magnetic field, the stator produces alternating current, the rectifier turns it into direct current, and the regulator controls the voltage.
| Measurement | Good value |
|---|---|
| Battery, engine off (fully charged) | about 12.6 V |
| Battery about half charged | about 12.0–12.1 V |
| Charging voltage, engine running | about 13.5–14.8 V |
Key on: the ECU check
In the first key position the system powers the important components and the ECU checks them. If everything is fine, the warning lights on the dashboard go out. If not, the ECU stores a fault code, which you can read with a diagnostic tool.
4 cases – where is the fault?
Case 1: Nothing happens
The engine doesn't turn at all. If the dashboard lights dim or go out when you turn the key, it's a power problem: the battery is flat or faulty, the terminals are loose or corroded, or the cable to the starter is broken. Measure the battery – a full one shows about 12.6 V. Rapid clicking also points to a weak battery. Clean and tighten the terminals, charge the battery or use jump leads.
Case 2: The starter whirs, but the engine doesn't turn
The circuit up to the starter works and its motor spins, but the pinion doesn't engage the flywheel. Check the solenoid, the drive pinion and the teeth on the flywheel ring gear. If you hear just a single click with a good battery, the solenoid or the starter itself is usually faulty, or its power supply is interrupted.
Case 3: The engine cranks, but doesn't start
Now you know the starting system works. Listen carefully – does it fire in any cylinder? The cause is in the ignition or the fuel supply.
- Diesel: check the glow plugs, especially in cold weather.
- Petrol: check the spark plugs, the ignition coils and their leads.
- Sensors: if the rev counter stays at zero while cranking, the crankshaft position sensor is suspect. Also check the camshaft sensor and the air mass sensor.
Case 4: Check the fuel
If the ignition is fine, only the fuel supply is left. Disconnect the fuel line somewhere after the pump, put it into a container and crank the engine. If fuel comes out, the system up to that point is fine. If not, the usual cause is the pump, its fuse or relay, or a clogged filter or line. On cars with electronic fuel control, the ECU or a sensor that feeds it can also be faulty.
Safety: work with no sparks or open flames near fuel, and never open high pressure diesel lines.
Summary
Nothing happens – check the battery and the cables. Starter whirs – check the starter and the flywheel. Cranks but won't start – check the ignition and the sensors. Then check the fuel supply, and read the fault codes with a diagnostic tool.
Frequently asked questions
Why does my car click but not start?
Rapid clicking usually means a weak or flat battery or poor terminal contact. A single click with a good battery usually points to the starter solenoid, the starter itself or its power supply.
What voltage should a car battery have?
About 12.6 V when fully charged with the engine off. With the engine running, the charging voltage should be about 13.5–14.8 V.
Why does the starter spin but not turn the engine?
The starter motor works, but the pinion doesn't engage the flywheel: check the solenoid, the drive pinion (bendix) and the teeth on the flywheel ring gear.
Why does the engine crank but not start?
Usually an ignition or fuel problem: glow plugs on a diesel, spark plugs and coils on a petrol engine, a faulty crankshaft sensor, or no fuel delivery.
How do I know if the crankshaft sensor is bad?
A typical sign is a rev counter that stays at zero while the engine is cranking. Read the fault codes and test the sensor before replacing it.
How do I check if the fuel pump delivers fuel?
Disconnect the fuel line after the pump into a container and crank the engine. If no fuel comes out, check the pump, its fuse and relay, and the filter and lines.
Related 3D diagnostics guides
- How to Check a Turbo – oil leaks, shaft play, blade damage and when to repair or replace the turbo.
- Intercooler Cleaning – where the oil comes from and how to clean the intercooler the right way.
- False Air / Vacuum Leaks – symptoms of unmetered air and 4 ways to find the leak.
- Crankshaft Position Sensor Test – no start, stalling when hot, limp mode and 4 tests for the CKP sensor.
- How to Test a MAF Sensor – power loss, high fuel consumption and 4 tests before you buy a new sensor.
- Clogged EGR Valve – black smoke, rough idle, how to test the EGR and clean it properly.
- Catalytic Converter vs DPF vs FAP – what each exhaust part does, lambda sensors and DPF regeneration.
- Losing Coolant – No Visible Leak – 4 hidden causes (head gasket, water pump seal, radiator, heater core) and the cooling system pressure test.
- Car Jerks When Accelerating – 8 causes – from spark plugs and injectors to the EGR, turbo, DPF and DSG gearbox – and what to check first.
- Engine Cranks a Long Time Before Starting – fuel pressure loss, the fuel pump check valve and 5 tests to find the faulty part.
More from Software for Cars
- 3D Automotive Diagnostics – all videos and guides on how car parts work, fail and are tested.
- How a Chiptuning File Is Made – step-by-step guide, including why the engine must be healthy and checked before tuning.
- Chiptuning Guides – free articles about chiptuning, ECU remapping, Bosch EDC16/EDC17 and checksum correction.
- Car Diagnostic Software – workshop diagnostic and repair software such as DiagBox, ODIS, OPCOM, Würth WOW, AutoData and ETKA.
- Chiptuning Software – ECU remapping, DPF/EGR off, DTC removal, IMMO off and checksum correction software (WinOLS, ECM Titanium, DaVinci and more). Download link sent by email after purchase.
- Chiptuning Files – large packages of ECU tuning files grouped by car brand or model.
- Individual ECU Tuning Files – single files for your exact ECU: the original (stock) file plus the modified file (Stage 1, Stage 2, DPF/EGR off).
- Tuning / Modification of ECU Maps – send us your original ECU file and we modify the map for your vehicle (paid with credits).
- Help with Software Installation – remote installation and setup of the software you bought, via AnyDesk.